HOW TO USE HAND-HELD STEAMER

Featured

Make sure that the H2O MOP X5™ is unplugged.
1) Fill the Water Tank with water.
Please refer to the “HOW TO USE THE H2O MOP X5™” section in this manual.
Attach either the round nylon brush or the round copper brush as explained in the “How to assemble Hand-Held Steamer” section in this manual.

2) Select one of the following Steam Regulator positions:
1 – Low, 2 – Medium, 3 – High or 4 – Hot Spray.
You can change the Steam Regulator position and
the steam output while operating the H2O MOP X5™.
3) Once the unit has been fully assembled and filled with water, plug in
the Power Cord into a grounded electrical outlet.
RED light – Power Indicator will indicate when power is on.
Power Switch ( O / I ) is in the OFF ( O ) position (higher position).
Wait for the Ready-to-Use indicator to turn Green – approximately 20 – 30 seconds.
GREEN light will turn on when the steam mop is ready for use.
When the Ready-to-Use indicator light turns green press the Power Switch ( O / I )
to the ON ( I ) position (lower position).
The Hand-Held Steamer will start emitting steam.

To stop emitting steam, turn OFF the unit by pressing the Power Switch ( O / I ) again. If the Power Switch ( O / I ) is pressed (lower position) prior to the Ready-to-Use light indicator turning green, water from previous use will not be heated and will be forced out
by present steam.

This may also happen if the Power Switch ( O / I ) was left in the ON ( I ) position (lower position) after previous use and the unit was disconnected by unplugging only. Make sure to turn the unit off after each use and then disconnect from the electrical outlet so the unit is in the OFF ( O ) position when used next time.
4) Slowly pass over surfaces to be cleaned.
Apply steam liberally.
Keep a towel handy and wipe away any excess water that may accumulate.
5) When the Hand-Held Steamer stops emitting steam, simply turn OFF and unplug
the unit, refill the Water Tank and continue cleaning.
To sanitize your work surfaces, kitchen countertops, sinks, bathrooms, etc., use
the Hand-Held Steamer over the same area for about 15 seconds.
Do not carry out this procedure on heat and steam sensitive surfaces.
The force and heat of the steam may adversely affect certain materials. Always
check the suitability of using the steamer on a particular surface by first testing
a hidden area.
Never direct steam towards people, animals or plants.

  • Do not use the steam to clean frozen windows.
  • Be careful when using the steamer on glass, as it may break.
  • Do not use steamer on leather, wax polished furniture or waxed
    floors, synthetic fabrics, velvet or other delicate steam-sensitive materials.
VN:F [1.9.18_1163]
Rating: 5.4/10 (41 votes cast)
VN:F [1.9.18_1163]
Rating: 0 (from 4 votes)

THE H2O MOP X5 HAND-HELD STEAMER

Featured

The Hand-Held Steamer is an ideal portable cleaner for use on work surfaces,
countertops, sinks, windows, mirrors, tiles and spot cleaning on floors, carpets and
rugs. Use it with the Jet Nozzle, Brass brush or Nylon brush attachments to spray
away dirt, grease, mold and more.

HOW TO ASSEMBLE HAND-HELD STEAMER

Make sure that the H2O MOP X5™ is unplugged before assembly.

1) Remove the Power Supply Cord from the upper cord wrap and cord holder,
turn the lower cord wrap to release the cord and remove the Power Supply Cord from its channel as illustrated in Fig. 1a & 1b.
2) Press the Extension Handle
lock button and remove the Extension Handle and the Curved Handle from the Main Body.
3) Press the Lock button on Main Body
and remove the Mop Head.

4) To attach the Jet Nozzle:
Insert the Jet Nozzle into the designated hole in the Main Body until it locks in place with
the Lock Button on the Main Body (you will hear a clicking sound), as illustrated in Fig. 4a.
Make sure that the Jet Nozzle is securely locked in place before usage.

5) Attach either the round nylon brush or round copper brush by screwing onto
the threaded end of the Jet Nozzle as illustrated in Fig. 5 a, b and c.
To remove either round brush, unscrew from the Jet Nozzle.

  • The round nylon brush is great for cleaning smooth hard surfaces,
    such as toilets, sinks, and kitchen counters, etc.
  • The round copper brush is great for cleaning coarse or metal surfaces, such as brick floors, car wheels, metal doors, and metal frames, etc.
  • Both brushes can also effectively clean the grease on pans, stoves and ovens in the kitchen. They can be used with soap or detergent to clean dirty areas.

Never use the round brass brush on surfaces that are prone to scratching.

VN:F [1.9.18_1163]
Rating: 2.7/10 (14 votes cast)
VN:F [1.9.18_1163]
Rating: +2 (from 2 votes)

Tips For Best Results:

Never leave the H2O MOP X5™ unattended while plugged in.

1) Sweep or vacuum floor prior to using the H2O MOP X5™.
2) To avoid puddling of water, the Microfiber Cloth must
be clean and dry for use. To replace the cleaning cloth,
proceed as follows: Let the cleaning cloth cool down,
remove cloth from unit, replace with a new Microfiber Cloth
(Optional Item) and continue use. Select low steam regulator
position.
3) To sanitize an area of your floor, leave the H2O MOP X5™
at high steam setting over the steam area for about 10 seconds,
but no longer than 15 seconds.
Do not carry out this procedure on heat and steam
sensitive floors.

  • Never steam at one spot for too long. This can cause floor surface damage.
  • Do not put hands or feet under the steam mop. Unit gets very hot.
  • During use a pulsing noise may be heard indicating that the mop is producing steam. This noise is normal.
  • There may be some minor “spitting” of water mixed with the steam. This is also normal.
  • The force and heat of the steam may adversely affect certain materials. Always check the suitability of using the steam mop on a surface by carrying out a preliminary test on a hidden area.
VN:F [1.9.18_1163]
Rating: 0.0/10 (0 votes cast)
VN:F [1.9.18_1163]
Rating: 0 (from 0 votes)

HOW TO USE THE H2O MOP X5™

Featured

PLEASE READ BEFORE USE

Test the H2O MOP X5™ on a small isolated area of your flooring prior to overall use
on any floor surface.
Always check the use and care instructions of your flooring manufacturer or
distributor before using the H2O MOP X5™.
When in doubt, please consult a flooring specialist. Only use the carpet glider
on carpeting and rugs. Use of the carpet glider on other floor surfaces will cause
streaking and possibly scratching.

1) Fill the Water Tank with water:
Make sure that the H2O MOP X5™ is unplugged.
Turn the Water Tank cap counter-clockwise approximately 90° to the
“OPEN” position and remove the cap as illustrated in Fig. 1a, b and c.

Hold the mop at a 45° angle as illustrated in Fig. 1d and add water in the tank up
to the MAX level by using the measuring cup.
Do not overfill. The maximum tank capacity is 400 ML/13.5 OZ.

Replace the Water Tank cap and turn clockwise approximately 90° to the “CLOSE” position until the cap is tightened securely. The H2O MOP X5™ uses tap water. However, in areas with hard water, distilled water should be used for better performance.
Make sure the Copper Cone inside the Water Tank is always submerged in water (As illustrated in Fig. 1i) while operating the H2O MOP X5™.

Never put cleaning detergents or scented products into the H2O MOP X5™.
This will make operation unsafe and damage the unit.
2) Select one of the following Steam Regulator positions:
1 – Low, 2 – Medium, 3 – High and 4 – Hot Spray
1 – Low and 2 – Medium Setting: Ideal for cleaning all hard floors, such as linoleum, ceramic, marble,
wood, etc.
3 – High Setting: Ideal for cleaning carpets and rugs.
4 – Hot Spray Setting: Ideal for cleaning
bathrooms, kitchens, window sills, car wheels, etc.
You can change the Steam Regulator position and change the steam output while operating the H2O MOP X5™.

3) Once the unit has been fully assembled and filled with water, plug in the Power
Cord to a grounded electrical outlet. The RED light – Power Indicator will indicate
when power is on. Power Switch ( O / I ) is in the OFF ( O ) position (higher position).
Wait for the Ready-to-Use indicator to turn Green – approximately 20 – 30 seconds.
GREEN light will turn on when the steam mop is ready for use.
When the Ready-to-Use indicator light turns Green press the Power Switch ( O / I )
to the ON ( I ) position (lower position). The mop will start emitting steam.
To stop emitting steam turn OFF ( O ) the unit by pressing the Power Switch ( O / I )
again.
If the Power Switch ( O / I ) is pressed (lower position) prior to Ready-to-Use light indicator turning green, water from the previous use will not be heated and will be forced out by present steam and will cause puddling to occur.
This may also happen if the Power Switch was left in the ON ( I ) position (lower position) from the previous use and the unit was disconnected by unplugging only. Make sure to turn
the unit OFF after each usage and then disconnect from the electrical outlet so the unit is in the OFF ( O ) position when used next time.

4) Slowly pass over the surface to be cleaned. The absorbent mop cloth picks up
the dirt loosened by the steam. Apply steam liberally. Keep a towel handy and wipe
away any excess water that may accumulate.
5) When the H2O MOP X5™ stops emitting steam, simply turn OFF and unplug
the appliance, refill the Water Tank and continue cleaning.

VN:F [1.9.18_1163]
Rating: 6.8/10 (10 votes cast)
VN:F [1.9.18_1163]
Rating: +3 (from 5 votes)

AFTER USE

Featured

  1. Unplug Power Cord from outlet.
  2. Allow Mop Pad/Cloths to cool down and carefully remove cleaning cloth from Mop Head, as cleaning cloth could still be hot.
  3. Any water remaining in the Water Tank should be emptied prior to appliance storage. Always empty the Water Tank at the end of each use.
  4. Let any water (that may remain as a product of condensation) drain from the steam opening prior to storing the appliance.
  5. Wrap Power Cord around Upper and Lower Cord Wrap.
  6. Wipe all surfaces of the H2O MOP X5™ with a soft cloth. Store in a protected, dry area.
  7. Please store the unit in a cool and dry place when not in use. Do not leave it exposed to sunlight or rain.
  8. Upright storage of the H2O MOP X5™ with a wet Mop Pad/Cloth may result in the formation of white marks on your floor. To remove the white marks, clean area with vinegar. Make sure to remove the Mop Pad/Cloth before storage.
VN:F [1.9.18_1163]
Rating: 8.5/10 (2 votes cast)
VN:F [1.9.18_1163]
Rating: 0 (from 0 votes)

CLEANING AND MAINTENANCE

Featured

BE SURE THAT THE UNIT IS DISCONNECTED FROM THE POWER OUTLET
WHEN PERFORMING CLEANING.

Drain the remaining water in the tank and clean the tank after every use.
Please use detergent to clean the accessories (Jet Nozzle and Round Brush) when
they are dirty, then wash with clean water and air dry.
How to decalcify the Water Tank interior:
To clean calcium deposits that build up inside the Water Tank, add one or two
tablespoons of white vinegar to a full Water Tank, close the Water Tank cap and
shake the contents. DO NOT TURN THE STEAMER ON.
Let the unit sit for a few hours. Then, empty the Water Tank and refill with clean
water and empty until it rinses clear.
DO NOT IMMERSE THE H2O MOP X5™ IN WATER.

  •   Cleaning procedure to remove lime scale

If your H2O MOP X5™ begins to produce steam more slowly than usual or stops
producing steam you may need to remove lime scale. Lime scale can develop over
time on the metal parts and greatly affect mop performance.
It is necessary to remove lime scale on a regular basis, every 25 – 50 times you use
a full tank of water or at least once a month, especially in areas with hard water.
The frequency of lime scale removal depends upon the hardness of your tap water
and how often you use the steam mop.
The H2O MOP X5‚Ñ¢ uses tap water. However, in areas with hard water,
distilled water should be used for better performance.
To remove lime scale from the H2O MOP X5™, please follow these procedures:
By using Scraper
1) Make sure that the H2O MOP X5™ is disconnected from the power supply before maintenance.
2) Use the Cleaning Pin to remove scale deposits from the small hole of the steam outlet in the Main Body, as illustrated in Fig. 2.
By swirling and pushing the pin up and down you will clean the steam outlet. Always ensure that all scale debris have been removed from the steam outlet before reassembling.
Continue swirling Cleaning Pin until no further debris is evident.
By using cleaning solution
1) Prepare a solution of 1/3 white vinegar and 2/3 tap water and add to the water tank.
2) Secure and position the unit to ensure steam released is aimed away from the floor or surrounding objects and surfaces. Plug the unit in, turn the unit ON by
pressing the Power Switch ( O / I ) and allow the unit to produce steam until the vinegar/water solution is used up.
3) Repeat the above procedure as many times as necessary until a normal steam flow rate is achieved.
4) Fill the Water Tank with fresh water and rinse out.
5) Fill the Water Tank with fresh water, attach to the unit and release steam through the system until the Water Tank is empty.
Do not leave the steamer unattended during the lime scale removal process and/or while in use.
Perform a test cleaning on a suitable isolated area after each lime scale removal to ensure that there is no debris left in the system.

VN:F [1.9.18_1163]
Rating: 4.0/10 (35 votes cast)
VN:F [1.9.18_1163]
Rating: +1 (from 5 votes)

IMPORTANT SAFEGUARDS

PLEASE READ CAREFULLY. FAILURE TO FOLLOW THE PRODUCT
INSTRUCTIONS WILL VOID YOUR WARRANTY.
READ ALL INSTRUCTIONS BEFORE USING THIS STEAM CLEANER.
As with any electric appliance, basic precautions should always be observed when
using this product, including the following:

  1. Verify that the main voltage indicated on the product corresponds with the
    voltage of your electrical outlet.
    Rated voltage: 110~120V, 60HZ, 1300W or 220~240V, 50/60HZ, 1300W
  2. To provide continued protection against risk of electric shock, only connect to
    properly grounded outlets.
  3. This product is designed for domestic use only.
  4. Do not use outdoors.
  5. Do not leave the H2O MOP X5™ unattended while plugged in. Unplug the
    electrical cord when not in use and before servicing.
  6. Do not allow the H2O MOP X5™ to be used as a toy. Young children should
    be supervised to ensure that they do not play with the appliance.
    Close attention is necessary when used near children, pets or plants.
  7. This appliance is not intended for use by persons (including children) with
    reduced physical, sensory or mental capabilities, or lack of experience and
    knowledge, unless they are under supervision have been instructed how to
    use the appliance by a person responsible for their safety.
  8. Never direct steam towards people, animals or plants.
  9. Do not immerse the H2O MOP X5™ in water or other liquids.
  10. Do not use with damaged cord or plug. If the H2O MOP X5™ is not working
    as it should, has been dropped, damaged, left outdoors, or immersed in
    water, return it to the distributor. If the supply cord is damaged, it must be
    replaced by the manufacturer or a qualified repair facility to avoid hazard.
  11. Do not pull or carry the unit by the cord, use the cord as a handle, close a
    door on the cord, or pull the cord around sharp edges or corners. Keep
    the cord away from heated surfaces.
  12. Never force the plug into an outlet.
  13. Do not use extension cords or outlets with inadequate electrical current
    carrying capacity.
  14. Unplug after each use. To safely unplug, grasp the plug and gently pull, do
    not unplug by pulling on the cord.
  15. Do not handle the plug or the H2O MOP X5™ with wet hands or operate
    without shoes.
  16. Do not insert any objects into openings in the unit. Do not use with any opening
    blocked.
  17. Do not use the Mop Head without floor cloth in place.
  18. Do not use without water in the Water Tank.
  19. Use extra caution when using on stairs.
  20. Store your H2O MOP X5™ indoors in a cool, dry place.
  21. Keep your work area well lit.
  22. Never put hot water or any other liquids such as aromatic, alcohol-based, or
    detergent products into the H2O MOP X5™ Water Tank. This will make the
    operation unsafe and damage the unit.
  23. Always keep the output for the steam clear. Avoid placing the steam
    opening on soft surfaces which may block the flow of steam. Keep the
    openings free from lint, hair and other potential obstructions to ensure
    proper steam flow.
  24. Use only as directed in this manual. Use only manufacturer’s recommended accessories.
  25. Use of attachments not provided or sold by the manufacturer or authorized resellers may cause fire, electric shock or injury.
  26. The liquid or steam should not be directed towards equipment containing electrical components, such as the interior of ovens.
  27. Do not expose to rain.
  28. Stop using the H2O MOP X5™ if you observe water leakage, and contact a qualified technician.
  29. Do not use the H2O MOP X5™ in enclosed spaces that are filled
    with flammable, explosive or toxic vapor such as paint thinner or oil-based paint.
  30. Do not use on leather, wax polished furniture or floors, unsealed hardwood or parquet floors, synthetic fabrics, velvet or other delicate steam-sensitive materials.
  31. Do not use for space heating purposes.
  32. Unplug appliance from outlet before servicing.
  33. Do not touch hot surfaces.
  34. Do not place on or near a hot gas or electric burner, or in a heated oven.
  35. To disconnect the unit, turn the Power Switch ( O / I ) to the “OFF” position, then remove plug from wall outlet.
  36. Do not use appliance for other than its intended use.
  37. Care should be taken when using appliance due to emission of steam.
  38. To avoid circuit overload, do not operate another appliance on the same socket (circuit) as the steam cleaner.
VN:F [1.9.18_1163]
Rating: 5.5/10 (2 votes cast)
VN:F [1.9.18_1163]
Rating: -1 (from 1 vote)

TROUBLESHOOTING GUIDE

Problem Possible Cause Solution
THE UNIT DOES NOT

POWER ON

The unit is not plugged in Make sure the unit is
plugged into a proper

outlet and the switch is ON ( I )

REDUCED STEAM OR

NO STEAM

Water Tank Empty

Blocked Steam Nozzle

Limescale Deposit

Fill Water Tank

Remove Mop Head and
Clean the Nozzle.

Follow cleaning procedure
to remove limescale in this
User’s Guide

STEAM ESCAPES

FROM CONNECTIONS

Attachment is not
connected properly

Debris or obstructions at
the connection points

Turn the unit OFF, allow it
to cool down, disconnect
the accessories and reattach
them.

Remove the accessory and
check and clean connection
points

THE CLEANING CLOTH

BECOMES WET

The cloth gets saturated
with water
Remove wet cloth and
replace with a dry cleaning
cloth or allow cloth to cool,
then wring out and reattach.
VN:F [1.9.18_1163]
Rating: 5.3/10 (14 votes cast)
VN:F [1.9.18_1163]
Rating: -4 (from 6 votes)